#Change router mac address linksys password#

Now, turn on modem, wait for a few seconds. To do so, first turn off the power to the router then to the modem. Try power-cycling the modem and router to fix this. Problem: You get an IP address, but are still unable to access internet. Try disabling them temporarily to see if this is the case. If you get the вЂњRequest Timed OutвЂќ error, this could be an issue with your antivirus or firewall. Enter 4.2.2.1 and 4.2.2.2 as the DNS addresses. In the window that comes up, select вЂњUse the following DNS server addressвЂќ. Right Click on Local Area Connection, then hit properties. To fix it, go to Start > Control Panel > Network and Internet > Network Connections. If you get four replies, then this is an issue with a DNS server. Torrents work for you, but browsing does not. Problem: You have a NAT mode connection, and you followed all the steps above. I can understand how frustrating they are, as it happened to me when setting up my own router! Common problems and solutionsД«elow are a few problems that cause your connection to not work even after following all steps above, and steps to solve them. Under Network > Router IP, change local IP to 192.168.2.1ДЇrom now, you should use this IP to access the router admin page. If your connection is in NAT mode, go to router admin page.

#Change router mac address linksys password#

Enter the Username and password you use to connect your modem to the network. If yours is in bridge mode, go to the router admin page, and change internet connection type to PPPOE. NAT mode is found on always-on internet connections, while bridge mode is used in connections where you have to connect manually with username / password combo. If you see any other address, it is in bridge mode. If you see IPv4 Address as 192.x.x.x, 172.x.x.x, 10.x.x.x, then you have it in NAT mode. Open a command prompt (type cmd in Start menu). Note it down вЂ“ you will need to enter it in every device you connect to.ДЇind out whether yours is a DSL line in bridge mode, or NAT mode. Avoid leaving it off (Disabled) or WEP, as they are easy to break in. It is advised to use WPA2 Personal, as it is the strongest. Configuring wireless security (encryption) вЂ“ WPA2 or WEP Wireless SSID Broadcast: Leave it enabled. Wireless Channel: Leave this on the default option, which is 6. You see this when searching for wifi on any device. Wireless Network Name(SSID): any name you want to give your wifi network. Under Basic Wireless Settings, select the following: Here, you can set up wifi, with necessary encryption etc. If so, you are connected to the internet.

It will have some value other than 0.0.0.0. Now, go to вЂњStatusвЂќ page, and look for IP address. Hit enable and click вЂњClone Your Mac-Address CloneвЂќ. Hit вЂњSave SettingsвЂќ.Д«ack on the admin page, click Mac Address Clone.

When prompted for username and password, leave username blank and type password as admin.ДЇrom the drop down menu on the page, select вЂњAutomatic Configuration DHCPвЂќ. Now that the connections between router, modem and computer are set up and tested, we need to tweak the settings from router administration page. Check that the corresponding light for net also comes on. Now, connect a cable between your ADSL modem and the вЂњInternetвЂќ port of the router. Check that the respective port number lights up on the top of the router. Now, connect a cable between your computer and any of the four LAN ports on the router. If not, your internet is not working properly. You should get a response of packets sent = 4 received = 4. Ensure that your net connection is working, by opening any page in a browser. Setup Linksys router with cable connectionД¬onnect the modem to your computer directly. If it does not work, follow the steps below to configure the router manually. You can try the Linksys setup wizard software. The reason is the greatly reduced RAM in the router. Sadly, newer versions of this seems to have reduced hardware capabilities, and therefore no support for DD WRT. The WRT54G2 V1 router that I have is popular, and supports custom firmware like DD-WRT and Tomato well. If you have any doubts or questions, leave them in comments below and IвЂ™ll try to help. Recently, I tried setting it up again, and presto, this time it worked! Below is a walkthrough, along with problems you may encounter and possible solutions. I gave up trying to set up the wifi router with my DSL modem then, and it has been accumulating dust in my attic ever since. I had purchased a Cisco Linksys WRT54G2 V1 router nearly two years ago.